Cisco 4200 Series

GigabitEthernet Copper Ports

Fixed copper GigabitEthernet (GE) interfaces are provided through standard RJ-45 connectors. These ports support the following features:

Standard 10/100/1000Base-T/TX operation with forced or auto-negotiation for speed and duplex.
Automatic crossover (auto-MDIX) for straight-through and crossover connections.
Pause flow control as defined by the 802.3x standard.
Maximum frame size of 9216 bytes.
Synchronous ENET operation that provides its recovered receive clock as an input clock source for the SETS as well as uses the system-wide reference clock to derive its transmit clock.

GE SFP Ports

The GE SFP ports support the following features:

100Base-FX and 1000Base-X SFP modules.
Digital optical monitoring as specified by the SFP.
Any mix of SFPs is supported unless specifically noted.

Pause flow control as defined by the 802.3x standard.
Maximum frame size of 9216 bytes.
Synchronous ENET operation that provides its recovered receive clock as an input clock source for the SETS as well as uses the system-wide reference clock to derive its transmit clock.

SFP+ Ports

The SFP+ ports support the following features:

Digital optical monitoring as specified by the optical transceiver module.
Any mix of SFPs is supported unless specifically noted.
Pause flow control as defined by the 802.3x standard.
Maximum frame size of 9216 bytes.

The following figure shows the 3D image of the Cisco NCS 4202:

Figure 1. Figure 3D Image of the Cisco NCS 4202

The following figures show the port numbering for the Cisco NCS 4202:

Figure 2. Front Panel of Cisco NCS 4202 —With DC Power Supply


1	Power Supply 0 (AC or DC)	10	Alarm port
2	Power Supply 1 (AC or DC)	11	Eight Copper port (1G PoE)
3	Front Air-Inlet Area	12	ToD port
4	GNSS RF IN (SMA threaded connector)	13	Management Port
5	SMB Snap-in connector (10MHZ)	14	USB Memory port
6	SMB Snap-in connector (1PPS)	15	USB Console port
7	Four 1G/10G SFP+	16	Zero Touch Provisioning button
8	Interface Module Slot	17	RS232 Console port
9	Four 1G SFP	18	RS232 Aux Console port

Figure 3. Rear View of the Cisco NCS 4202


1	Fan tray	3	Air vents
2	Grounding lug	—

Table below describes the other features of Cisco NCS 4202 (AC and DC).

Table 1. Cisco NCS 4202 Specifications

Specification

NCS 4202

DimensionWidth x Depth x Height

23.06 x 16.43 x 1.73 inches

Weight

Total weight: 5.63 kg

Weight of PSU: 0.59 kg

Weight of Fan: 0.33 kg

Rack Unit

EIA one RU

Airflow

Front to back

Cable access

Front cable access

System throughput

60 Gbps, 95 Mpps

Power Supply

Redundant

Yes

Voltage Range

85V AC to 264V AC, nominal 100/240 VAC

Frequency Range

47 Hz to 63 Hz, nominal 50/60 Hz

Maximum Power

360 W

Yes

Voltage Range

-18 VDC to -32 VDC or -40 VDC to -72 VDC

Nominal Voltage Range

-24 VDC/-48 VDC/-60 VDC

Maximum Power

375 W

Heat Dissipation

—

Operating Temperature/Humidity

–40º C to 70º C

Alarms

4 alarm dry contact inputs (normally open)
LED indicators for critical, major, and minor alarms

Supported Interface Modules

8 port RJ48C T1/E1 Interface Module

Mounting option

Front Z-bracket mount for 23 inches rack

Port Configuration

12x1G and 4x10G/1G ports

Port Numbering

4x10G SFP+ – Port [12:15]

Note	Ports 12 to 15 are Dual Rate ports

4x1G SFP – Port [8:11]

8x1G PoE RJ45/Cu ports [0:7]

Copper/1G/10G Port LEDs

Link/Activity/Fault

Temperature Sensors

Four temperature sensors

1PPS/ToD

External ports for 1PPS/TOD

PoE

Provides power over Ethernet

GNSS

Connects to the external GPS